中華人民共和國國家標準(中國大陸GB標準)英文版 |
GB標準是中華人民共和國國家標準,也叫GB國標,是中國大陸強制執行的國家標準,所有中國大陸境內銷售的商品及提供服務都必須符合GB國家標準的要求,包括進口商品及服務; 本網站提供GB國家標準的查詢檢索,英文版翻譯,GB標準產品檢測檢驗及合規性分析服務; |
GB/T 42951-2023 计时仪器 硬材料制造的手表外观件 一般要求和试验方法(中英文版) Timing instruments. Appearance parts of watches made of hard materials. General requirements and test methods. |
|||
GB/T 42554-2023 计量器具环境试验的通用要求(中英文版) General requirements for environmental testing of measuring instruments |
|||
GB/T 42399.3-2023 无损检测仪器 相控阵超声设备的性能与检验 第3部分:组合系统(中英文版) Non-destructive testing instruments - Performance and inspection of phased array ultrasonic equipment - Part 3: Combined systems |
|||
GB/T 42399.2-2023 无损检测仪器 相控阵超声设备的性能与检验 第2部分:探头(中英文版) Non-destructive testing instruments - Performance and inspection of phased array ultrasonic equipment - Part 2: Probes |
|||
GB/T 42399.1-2023 无损检测仪器 相控阵超声设备的性能与检验 第1部分:仪器(中英文版) Non-destructive testing instruments - Performance and inspection of phased array ultrasonic equipment - Part 1: Instruments |
|||
JY/T 0213—2022 教学用非电工电子仪器环境试验(中英文版) Environmental test of non-electrical and electronic instruments for teaching |
|||
GB/T 21838.3-2022 金属材料 硬度和材料参数的仪器化压入试验 第3部分:标准块的标定(中英文版) Metallic materials - Instrumented indentation tests for hardness and material parameters - Part 3: Calibration of standard blocks |
|||
GB/T 21838.2-2022 金属材料 硬度和材料参数的仪器化压入试验 第2部分:试验机的检验和校准(中英文版) Metallic materials - Instrumented indentation tests for hardness and material parameters - Part 2: Verification and calibration of testing machines |
|||
GB/Z 41476.3-2022 无损检测仪器 1MV以下X射线设备的辐射防护规则 第3部分:450kV以下X射线设备辐射防护的计算公式和图表(中英文版) Non destructive testing instruments - radiation protection rules for X-ray equipment below 1mV - Part 3: calculation formulas and charts for radiation protection of X-ray equipment below 450kv |
|||
GB/Z 41476.4-2022 无损检测仪器 1MV以下X射线设备的辐射防护规则 第4部分:控制区域的计算(中英文版) Non destructive testing instruments - radiation protection rules for X-ray equipment up to 1mV - Part 4: Calculation of control area |
|||
GB/T 12810-2021 实验室玻璃仪器 玻璃量器的容量校准和使用方法(中英文版) Laboratory glassware—Capacity methods testing and use of volumetric instruments |
|||
GB/T 40023-2021 无损检测仪器 超声衍射声时检测仪 技术要求(中英文版) Non-destructive testing instruments - Ultrasonic time-of-flight diffraction instrument - Technical requirements |
|||
GB/T 39849-2021 无损检测仪器 超声衍射声时检测仪 性能测试方法(中英文版) Non-destructive testing instruments—Ultrasonic time-of-flight diffraction instrument—Methods of performance tests |
|||
GB/T 40968-2021 乐器产品中多环芳烃的测试方法(中英文版) Test method of polycylic aromatic hydrocarbons in musical instrument |
|||
RB/T 039-2020 检测实验室仪器设备计量溯源结果确认指南(中英文版) Guidelines for the Confirmation of Measurement Traceability Results of Testing Laboratory Instruments and Equipment |
|||
MT/T 1191-2020 煤矿井下锚杆锚固参数机械波无损检测仪通用技术条件(中英文版) General technical conditions of mechanical wave non-destructive testing instrument for anchor bolt anchoring parameters in coal mines |
|||
JB/T 13809-2020 固体材料力学性能原位测试仪器 通用技术条件(中英文版) In situ testing instrument for mechanical properties of solid materials - General technical conditions |
|||
GB/T 18779.5-2020 产品几何技术规范(GPS) 工件与测量设备的测量检验 第5部分:指示式测量仪器的检验不确定度(中英文版) Geometrical product specifications (GPS)—Inspection by measurement of workpieces and measuring equipment—Part 5: Uncertainty in verification testing of indicating measuring instruments |
|||
GB/T 39555-2020 智能实验室 仪器设备 气候、环境试验设备的数据接口(中英文版) Intelligent laboratory—Instruments and equipment—Data interface of climatic and environmental testing equipment |
|||
GB/T 39635-2020 金属材料 仪器化压入法测定压痕拉伸性能和残余应力(中英文版) Metallic materials—Measurement of indentation tensile properties and residual stresses by an instrumented indentation test |
找到:128條目 | [首頁]-[上一頁]-[下一頁]-[尾頁] | 去到: 1 2 3 4 5 6 7 |